Rocky View · Frigidaire Repair Specialists

Frigidaire Appliance Repair

Years of fixing Frigidaire fridges, ranges and laundry units mean no fault catches us off guard. Serving Calgary, Airdrie, Chestermere and Okotoks.

Frigidaire Appliances We Service

Where We Work

Four local offices delivering fast, same-day appliance repair right across the Calgary region.

Calgary 4624 16 Ave NW, Unit C, AB T3B 1J1

Airdrie 401 Coopers Blvd SW, Unit 5, AB T4B 4J3

Chestermere 20 Dawson Wharf Mount #1112, AB T1X 2Z5

Okotoks 258 Northridge Dr, Unit C, AB T1S 1R1

Tap an appliance group to see the warning signs we hear most — and how we put them right.

Fridge not cooling but lights work Often a failed evaporator fan or start relay We test the evaporator fan and compressor start relay, replace the failed part, and confirm the fridge holds a steady temperature.
Ice maker or water dispenser stops working Usually a frozen water line or faulty inlet valve We thaw the water line, test the inlet valve and dispenser switch, replace what's failed, and verify smooth ice and water flow.
Excess frost or ice in the freezer Typically a defrost timer or heater fault We test the defrost timer, heater and thermostat, replace the failed component, and confirm the auto-defrost cycle runs as it should.
Loud humming or fridge won't stay running Commonly a compressor or condenser fan fault We diagnose the compressor and condenser fan, replace the faulty part with a genuine match, and confirm quiet, continuous cooling.
Water leaking onto the floor Often a clogged defrost drain or cracked drain pan We flush the blocked defrost drain, replace any cracked pan or tubing, and leak-test the unit to make sure it stays dry.

Washer won't drain or finish the cycle Usually a clogged drain pump or pressure switch We clear the drain pump and hose, test the pressure switch, replace what's failed, and run a full cycle to confirm draining.
Loud noise or shaking during spin Often worn drum bearings or shock absorbers We replace the worn bearings or shock absorbers, rebalance the drum, and run a high-speed spin to confirm it runs smoothly.
Dryer runs but produces no heat Typically a failed heating element or thermal limiter We test the heating element, thermostat and thermal limiter, replace the failed part, and confirm safe, even heat across a full cycle.
Error code shown on the control panel Commonly a sensor, motor or control board fault We decode the Frigidaire error, trace it to the failing part, replace it, and clear the fault before testing every program.
Dryer drum won't turn Often a snapped drive belt or seized idler pulley We fit a new drive belt and idler pulley, check the drum rollers, and confirm the drum turns freely through a complete cycle.

Dishes left dirty or filmy Usually clogged spray arms or a weak wash motor We clear the spray arms and filters, test the wash motor pressure, replace it if weak, and run a verification wash cycle.
Water won't drain from the tub Often a blocked drain hose or faulty drain pump We clear the drain hose and check valve, replace the drain pump if needed, and confirm the tub empties fully each cycle.
Dishwasher leaking during a wash Typically a worn door seal or cracked spray arm We replace the worn door gasket or cracked spray arm, check the water inlet, and pressure-test to make sure it stays watertight.
Buttons unresponsive or won't start Commonly a faulty door latch or touchpad We replace the failed latch or touchpad, inspect the control board, and confirm the dishwasher starts reliably every time.
Stops mid-cycle or won't heat the water Often a heating element or thermostat fault We test the heating element and high-limit thermostat, replace the failed part, and run a full cycle to confirm hot, clean washes.

Oven won't heat or bakes unevenly Usually a burnt-out bake element or igniter We test the bake and broil elements or gas igniter, replace the failed part, and confirm even, accurate heat throughout the oven.
Oven temperature is off or won't hold Often a faulty temperature sensor needing calibration We check the sensor against a calibrated thermometer, replace it if faulty, and recalibrate so the oven holds the set temperature.
Surface element won't heat or stays on Typically a bad element or infinite switch We test each element and infinite switch, replace the failed component, and confirm reliable, controllable heat on every burner.
Control panel dark or buttons stuck Commonly an electronic control board fault We inspect the control board and connectors, repair or replace the failed board, and test every burner and oven function afterwards.
Self-clean fails or door won't unlock Often a door lock motor or thermal switch fault We replace the door lock motor or thermal switch, verify the locking mechanism, and run a self-clean cycle to confirm it completes.