Call Now Request Callback
Call Now Request Callback
Samsung appliance repair technician
Rocky View · Authorised Samsung Repair Specialists

Samsung Appliance Repair

Samsung specialists who handle even the trickiest faults — across Calgary, Airdrie, Chestermere and Okotoks.

Call to Anytime (368) 338-2261 click and fill out the form Book a Visit

Samsung Appliances We Service

Where We Work

Service Areas

Four local offices delivering fast, same-day appliance repair right across the Calgary region.

Calgary 4624 16 Ave NW, Unit C, AB T3B 1J1
Airdrie 401 Coopers Blvd SW, Unit 5, AB T4B 4J3
Chestermere 20 Dawson Wharf Mount #1112, AB T1X 2Z5
Okotoks 258 Northridge Dr, Unit C, AB T1S 1R1
Service area map showing Calgary, Airdrie, Chestermere and Okotoks

Common Samsung Faults We Fix Every Day

Tap an appliance group to see the warning signs we hear most — and how we put them right.

01
01

Fridge & Freezer

Fridge & Freezer

  • Not cooling, or the freezer ices over Likely a faulty defrost sensor or failing compressor We test the sealed system and defrost circuit, replace the failed sensor or relay, and verify steady cooling before we leave.
  • Water pooling under the drawers Usually a clogged or frozen defrost drain We thaw and flush the blocked drain line, clear any ice buildup, and fit a drain heater clip so it stays clear.
  • Loud buzzing or clicking at the back Often a worn evaporator fan or start relay We pinpoint the noisy part, swap the worn fan motor or compressor relay with a genuine match, and confirm quiet, normal running.
  • Flashing error code on the display Typically a sensor fault or control board issue We read the fault code, trace it to the failing sensor or board, replace the faulty component, and clear the error.
  • Frost build-up inside the cabinet Commonly a worn door seal or stuck damper We replace the damaged gasket or free the stuck air damper, restore the proper seal, and check temperatures across every shelf.
02
02

Washer & Dryer

Washer & Dryer

  • Won't drain, or water stays in the tub Usually a blocked drain pump or filter We clear the pump and filter of debris, check the drain hose for kinks, and run a full cycle to confirm draining.
  • Banging or grinding during the spin Often worn tub bearings or a loose drum We strip down the drum, replace the worn bearings and seals, rebalance the load sensor, and test the spin at full speed.
  • Drum won't spin, clothes stay wet Typically a broken drive belt or motor fault We fit a new drive belt or motor coupling, check the motor control board, and verify the drum spins freely and drains properly.
  • Dryer runs but won't heat Commonly a failed heating element or thermal fuse We test the element, thermostat and thermal fuse, replace whichever has failed, and confirm safe, even heat through a full drying cycle.
  • Stops mid-cycle with an error code Often a faulty sensor or control board We diagnose the exact code, replace the failing sensor or board, then run repeated cycles to make sure it completes every time.
03
03

Dishwasher

Dishwasher

  • Dishes still dirty after a full cycle Usually clogged spray arms or a weak wash pump We clear the spray arms and filters, test the wash pump pressure, replace it if weak, and run a verification wash.
  • Won't drain, water sits at the bottom Often a blocked drain hose or faulty pump We clear the drain hose and check valve, replace the drain pump if needed, and confirm the tub empties fully each cycle.
  • Leaking onto the floor Typically a worn door gasket or cracked hose We trace the leak to its source, replace the worn door seal or split hose, and pressure-test to make sure it's watertight.
  • Won't start or the door won't latch Commonly a broken door switch or latch assembly We replace the faulty latch or door switch, check the wiring harness, and confirm the dishwasher starts reliably every time.
  • Stops partway with a code lit up Often a heating or sensor fault on the control board We read the code, replace the failed heater or sensor, reset the control board, and run a full cycle to confirm the fix.
04
04

Stove, Range & Oven

Stove, Range & Oven

  • A burner or element won't heat Usually a burnt-out element or igniter We test each element and igniter, replace the failed part with a genuine component, and confirm even, reliable heat across every burner.
  • Oven won't reach the set temperature Often a faulty bake element or temperature sensor We check the element and sensor against a calibrated reading, replace the faulty part, and recalibrate so the oven holds temperature.
  • Touch controls or display go dark Typically a control board or ribbon connector fault We inspect the control board and connectors, repair or replace the failed board, and test every function on the panel afterwards.
  • Self-clean fails or door won't lock Commonly a broken door lock motor or switch We replace the door lock motor or switch, verify the locking mechanism, and run the self-clean cycle to confirm it completes safely.
  • Error code, or a faint gas smell Often a gas valve, igniter or safety sensor issue We safely test the gas valve and igniter, replace any faulty safety component, and leak-check every connection before signing off.
Rocky View technician

Request a Service

Working Hours

Mon – Sun: 7 AM – 11 PM

Call Us Directly

(368) 338-2261

Book Your Repair

Fill out the form and we’ll get back to you shortly.