Call Now Request Callback
Call Now Request Callback
Maytag appliance repair technician
Rocky View · Maytag Repair Specialists

Maytag Appliance Repair

Maytag builds them tough, and we keep them that way — even the stubborn faults are no match for our techs. Serving Calgary, Airdrie, Chestermere and Okotoks.

Call to Anytime (368) 338-2261 click and fill out the form Book a Visit

Maytag Appliances We Service

Where We Work

Service Areas

Four local offices delivering fast, same-day appliance repair right across the Calgary region.

Calgary 4624 16 Ave NW, Unit C, AB T3B 1J1
Airdrie 401 Coopers Blvd SW, Unit 5, AB T4B 4J3
Chestermere 20 Dawson Wharf Mount #1112, AB T1X 2Z5
Okotoks 258 Northridge Dr, Unit C, AB T1S 1R1
Service area map showing Calgary, Airdrie, Chestermere and Okotoks

Common Maytag Faults We Fix Every Day

Tap an appliance group to see the warning signs we hear most — and how we put them right.

01
01

Fridge & Freezer

Fridge & Freezer

  • Fridge section warm, freezer still cold Often a failed evaporator fan or damper control We test the evaporator fan and air damper, replace the failed part, and confirm balanced cooling between fridge and freezer before leaving.
  • Ice maker stops or jams up Usually a faulty ice-maker assembly or water valve We test the ice-maker module and water inlet valve, replace whichever has failed, and run a full cycle to verify clean ice.
  • Heavy frost build-up in the freezer Typically a defrost heater or thermostat fault We test the defrost heater, thermostat and timer, replace the failed component, and confirm the auto-defrost cycle runs correctly.
  • Fridge runs loud or won't stay cold Commonly a compressor or start relay fault We diagnose the compressor and start relay, replace the faulty part with a genuine match, and confirm quiet, steady cooling.
  • Water pooling under the unit Often a clogged defrost drain or cracked pan We flush the blocked defrost drain, replace any cracked pan or tubing, and leak-test the system to make sure it stays dry.
02
02

Washer & Dryer

Washer & Dryer

  • Washer won't drain or spin out Usually a worn drive belt, pump or lid switch We replace the worn belt, clear the drain pump and test the lid switch, then run a full cycle to confirm draining and spinning.
  • Loud banging or knocking on spin Often worn tub bearings or a failed shock We replace the worn bearings or shock absorbers, rebalance the drum, and run a high-speed spin to confirm smooth, quiet operation.
  • Dryer tumbles but produces no heat Typically a failed element or thermal fuse We test the heating element, thermostat and thermal fuse, replace the failed part, and confirm safe, even heat through a full cycle.
  • F-code or error shown on the display Commonly a sensor, motor or control board fault We decode the Maytag F-code, trace it to the failing part, replace it, and clear the fault before testing every program.
  • Dryer won't start or stops early Often a faulty door switch or start circuit We test the door switch, thermal fuse and start circuit, replace the failed part, and confirm it runs a full cycle reliably.
03
03

Dishwasher

Dishwasher

  • Dishes still dirty after the cycle Usually clogged spray arms or a worn wash pump We clear the spray arms and filters, test the wash pump and chopper, replace worn parts, and run a verification wash cycle.
  • Water won't drain from the tub Often a blocked drain hose or faulty pump We clear the drain hose and check valve, replace the drain pump if needed, and confirm the tub empties fully each cycle.
  • Leaking onto the kitchen floor Typically a worn door seal or cracked hose We replace the worn door gasket or split hose, check the water inlet valve, and pressure-test to make sure it stays watertight.
  • Won't start or lights keep flashing Commonly a door latch or control board fault We replace the faulty latch or touchpad, inspect the control board, and confirm the dishwasher starts reliably every time.
  • Stops mid-cycle or water stays cold Often a heating element or thermostat fault We test the heating element and high-limit thermostat, replace the failed part, and run a full cycle to confirm hot, clean washes.
04
04

Stove, Range & Oven

Stove, Range & Oven

  • Oven won't heat or bakes unevenly Usually a burnt-out bake element or igniter We test the bake and broil elements or gas igniter, replace the failed part, and confirm even, accurate heat throughout the oven.
  • Oven temperature runs hot or cold Often a faulty temperature sensor needing calibration We check the sensor against a calibrated thermometer, replace it if faulty, and recalibrate so the oven holds the set temperature.
  • A burner won't light or heat Typically a bad igniter, element or switch We test each burner igniter, element and infinite switch, replace the failed component, and confirm reliable heat on every burner.
  • Control panel dead or unresponsive Commonly an electronic control board fault We inspect the control board and wiring, repair or replace the failed board, and test every burner and oven function afterwards.
  • Self-clean won't run or door stays locked Often a door lock motor or thermal fault We replace the door lock motor or thermal switch, verify the locking mechanism, and run a self-clean cycle to confirm it completes.
Rocky View technician

Request a Service

Working Hours

Mon – Sun: 7 AM – 11 PM

Call Us Directly

(368) 338-2261

Book Your Repair

Fill out the form and we’ll get back to you shortly.